UK Delivery Free Over £200
VP45/AC 220V 50HZ VANE PUMP 35 L/MIN

VP45/AC 220V 50HZ VANE PUMP 35 L/MIN

SUBMERSIBLE PUMP STRAINER - UP500

SUBMERSIBLE PUMP STRAINER - UP500

UP12/E-DX 24V Dual Variable Speed Electronic Fresh Water Pump System 72 Litres per Minute +PCS 3.5 BAR

Self-priming water pressure systems with two connected pumps with electronic control speed motor related to the flow rate. Delayed start of the auxiliary pump. Reduced consumption and noise. Accumulator tank is not required. Protected against overloads. Pump functions monitored by 2 LEDs. “Empty tank” signal and shut-off device. Available also with control panel. Two versions available, 2.5 bar and 3.5 bar. Both versions are 24Vdc. The item presented on this page is the 3.5 bar variant.

This pump features Marco's Intelligent Brain ECU system.  The pump is able to detect the constant pressure in the plumbing system and respond accordingly when the pressure drops caused by an outlet being used.  The means that the pump can respond to demand and only ever works at the appropriate speed for any given usage.  Advantages of this system include:

  • Quieter running - pump rarely needs to run at full speed
  • Longer lasting - a more mechanically sympathetic arrangement
  • Less consumption
  • No need for accumulator/expansion tank*
  • Intelligent programming and inclusion with digital switching systems
  • Fault finding - ECU logs error codes and allows for faster diagnostics

 

* Please consult our technical department if intending to install this pump without an accumular tank.  There are some scenarios in which an accumulator tank will still be required.

SKU
16468613
£1,754.66 £1,462.22
IP67 ingress protection
Dust tight, protected against temporary immersion in water.
ISO8849
Product complies with ISO 8849 standards
ISO8846
Product complies with ISO 8846 standards

Marco Patented Motor Flange Technology

The innovative flange which isolates the motor housing from the pump gears is an industry first. This clever piece of product design has extended the life expectancy of the Marco pump range, removing the possibility of pump failure caused by condensation build-up in the motor housing. When the pump runs, heat is generated by the spinning motor. Cool water passing through the pump head then adds the conflicting temperature, causing condensation to build. Marco's new flange design allows this condensation to escape the motor housing.

Sealed and dry motor for extended life of the brushes and lower power consumption

Enhanced motor protection

Best performance in extreme hot and cold environments

Highly extended range of fluid temperature tolerance

Thermal and mechanical decoupling for reduced wear and extended seal life

Improved resistance to chemicals

Locked alignment of the pump head 

Product Drawing

PEEK Gears

The PEEK gears guarantee constant pressure, heavy duty cycles, lower noise levels and excellent resistance to chemicals. The pump also features a nickel plated brass body and connections, stainless steel shaft, FKM seals and NBR O-rings. The pump is built to last and perform to the highest standard.

Electronic Pressure Sensor

The PEEK gears guarantee constant pressure, heavy duty cycles, lower noise levels and excellent resistance to chemicals. The pump also features a nickel plated brass body and connections, stainless steel shaft, FKM seals and NBR O-rings. The pump is built to last and perform to the highest standard.

Constant control of pressure, voltage and electrical draw

Protection of the pump from short circuits and overvoltage

Automatic stop when no more liquid is present

Reduction in electrical interferences thanks to the gradual acceleration of the motor

Noise reduction during operation

Optimisation of electrical draw

Reduced wear of components and increased life span of the system

Operative functions signaled by LEDs

*Expansion tank can be ommitted from the circuit as the pump quickly responds to pressure change. TIMAGE reccomends the use of an expansion/accumulator tank in larger plumbing circuits or circuits with washer dryers fitted. Please consult the TIMAGE technical team with any queries: technical@timage.co.uk 

 

 

PCS Control Panel

A pair of the PCS control panels are included with the UP12/E-DX pump. Connecting to the pumps using the network cable, the panels can be used to remotely monitor the operation of the pumps and interact with them.

Remote monitoring of the pump operation and interaction with it: checking of liquid presence and reset in case of malfunction without disconnecting the device.

The “Run” LED indicates that the pump is working and alerts in case of small leaks
in the system, preventing motor damage due to prolonged operation at low speed.

Stop and Start of the pump with a simple push of a button.

Quick connection of the panel to the 3m RJ11/6 terminal cable integrated in the sensor of the pump.

The panel can be recessed in a circular hole of a 70mm diameter or externally
mounted.

The terminal block allows the user to replicate the buttons and leds of the panel
on an external circuit thus favoring a personalized management of the functions
through an external device designed by third parties.

More Information
Input Voltage 24Vdc
Flow Rate 72 l/min
Pressure 3.5 bar
Liquid Type Fresh water
Power Consumption 20 Amps
Motor Power 360W x2
Fuse 30 Amps
Weight (kg) 21.700000
Manufacturer Marco
EAN Barcode 8022278608315
Download as PDF Download as PDF
We found other products you might like!